rclone lsd blomp: -vv
2026/09/05 10:41:17 DEBUG : rclone: Version "v1.75.1" starting with parameters ["rclone" "lsd" "blomp:" "-vv"]
2026/09/05 10:41:17 DEBUG : Creating backend with remote "blomp:"
2026/09/05 10:41:17 DEBUG : Using config file from "C:\Users\...\AppData\Roaming\rclone\rclone.conf"
2026/09/05 10:41:17 CRITICAL: Failed to create file system for "blomp:": didn't find section in config file ("blomp")
using gui (and rclone lsd blomp: -vv in cmd at the end)
rclone lsd blomp: -vv
2026/09/05 10:43:59 DEBUG : rclone: Version "v1.75.1" starting with parameters ["rclone" "lsd" "blomp:" "-vv"]
2026/09/05 10:43:59 DEBUG : Creating backend with remote "blomp:"
2026/09/05 10:43:59 DEBUG : Using config file from "C:\Users\...\AppData\Roaming\rclone\rclone.conf"
2026/09/05 10:43:59 CRITICAL: Failed to create file system for "blomp:": didn't find section in config file ("blomp")
rclone.conf (create by program)
[BlompTest] // cmd
type = swift
user = myMail
key = myPassoword
auth = https://authenticate.ain.net
user_id = MyUser
domain = myMail
that "didnt find section in config file (blomp)" usually means the remote name in the gui and the one you typed in cmd dont match, or the gui never wrote the config. in my experience after rclone config, run rclone listremotes and use whatever name actually shows up (case sensitive). your redacted config shows BlompTest / BlompTest2 not blomp, so try rclone lsd BlompTest: -vv. also blomp is just swift under the hood so if the remote exists but lists empty, double check the auth url / tenant from blomp docs, ive fat fingered that before and gotten a quiet empty listing.
2026/09/13 18:37:05 DEBUG : rclone: Version "v1.75.1" starting with parameters ["rclone" "lsd" "BlompTest:" "-vv"]
2026/09/13 18:37:06 DEBUG : Creating backend with remote "BlompTest:"
2026/09/13 18:37:06 DEBUG : Using config file from "C:\Users\...\AppData\Roaming\rclone\rclone.conf"
2026/09/13 18:37:06 CRITICAL: Failed to create file system for "BlompTest:": Can't find AuthVersion in AuthUrl - set explicitly
I had seen that discussion, and I would have posted there if it hadn't been closed.
Yes, I made two attempts. But I see that in your case, one is “blomp” and the other is “blomp_remote.” Are these two separate attempts, or is one required for the other?
Note: By “myemail,” I mean the full domain address.
Before we talk about aliases, I'd like to resolve this issue.
I tried the configuration shown in the other thread again, even though I was told not to edit the config file manually.
This time I've got CRITICAL: Failed to create file system for "blomp-swift3:": HTTP Error: 404: 404 Not Found. And when you open it from here, it's obviously empty.
[blomp-swift3]
type = swift
user = email@example.com
key = PASSWORD
auth = https://authenticate.blomp.com
tenant = storage
auth_version = 2
no_chunk = true
You can click on the screenshots to enlarge them. However, since it causes problems, I've decided to remove them.
True. Mine is missing some parts. At this point, since I've already failed 1,000 times following other instructions, please write me a foolproof guide on how to add a blomp in the easiest way possible. Either the GUI or the terminal is fine at this point.
You keep missing steps that @asdffdsa points out as he already shared it works with an above post. If you can get your remote configurated correctly, it worsk fine.